| 詳細參數 | |||
|---|---|---|---|
| 品牌 | other | 型號 | FLA6041 |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 硬PLC | 加工定制 | 否 |
FLA6041
抑制電網引入的干擾對于電源引入的電網干擾可以安裝一臺帶屏蔽層的變比為1：1的隔離變壓器，以減少設備與地之間的干擾，還可以在電源輸入端串接LC濾波電路。正確選擇接地點，完善接地系統良好的接地是保證PLC可靠工作的重要條件，可以避免偶然發生的電壓沖擊危害。接地的目的通常有 兩個，其一為了安全，其二是為了抑制干擾。完善的接地系統是PLC控制系統抗電磁干擾的重要措施之一。PLC控制系統的地線包括系統地、屏蔽地、交流地和保護地等。接地系統混亂對PLC系統的干擾主要是各個接地點電位分布不均，不同接地點間存在地電位差，引起地環路電流，影響系統正常工作。例如電纜屏蔽層必須一點接地，如果電纜屏蔽層兩端A，B都接地，就存在地電位差，有電流流過屏蔽層，當發生異常狀態如雷擊時，地線電流將更大。
蔽層、接地線和大地有可能構成閉合環路，在變化磁場的作用下，屏蔽層內又會出現感應電流，通過屏蔽層與芯線之間的耦合，干擾信號回路。若系統地與其他接地處理混亂，所產生的地環流就可能在地線上產生不等電位分布，影響PLC內邏輯電路和模擬電路的正常工作。PLC工作的邏輯電壓干擾容限較低，邏輯地電位的分布干擾容易影響PLC的邏輯運算和數據存儲，造成數據混亂、程序跑飛或死機。模擬地電位的分布將導致測量精度下降，引起對信號測控的嚴重失真和誤動作。安全地或電源接地：將電源線接地端和柜體連線接地為安全接地。如電源漏電或柜體帶電，可從安全接地導入地下，不會對人造成傷害。系統接地：PLC控制器為了與所控的各個設備同電位而接地，叫系統接地。接地電阻值不得大于4 Ω，一般需將PLC設備系統地和控制柜內開關電源負端接在一起，作為控制系統地。
In addition, the shielding layer, grounding wire and earth may b a closed loop. Under the b of changing magnetic field, induced current will appear in the shielding layer, which will interfere with the signal loop through the coupling between the shielding layer and the core wire. If the system ground and other grounding treatments are confused, the generated ground circulation may produce unequal potential distribution on the ground wire, affecting the normal operation of logic circuit and analog circuit in PLC. The logic voltage interference tolerance of PLC is low, and the distribution interference of logic ground potential is easy to affect the logic operation and data storage of PLC, resulting in data confusion, program flying or crash. The distribution of analog ground potential will lead to the decline of measurement accuracy and serious distortion and misoperation of signal measurement and control.
Safety grounding or power grounding: connect the grounding terminal of the power line and the cabinet to safety grounding. If the power supply leaks or the cabinet is charged, it can be led underground from the safe grounding without causing harm to people.
System grounding: PLC controller is grounded in order to have the same potential with each equipment controlled, which is called system grounding. The grounding resistance value shall not be greater than 4 Ω. Generally, the PLC equipment system ground and the negative terminal of the switching power supply in the control cabinet shall be connected together as the control system ground.
