| 詳細參數 |
|---|
農用混流泵A靈壽農用混流泵400HW-7
（四）長軸深井泵長軸深井泵是一種單吸多級立式長軸離心泵，可供城市工礦企業給排水及農田灌溉從深井中提水之用。長軸深井泵的動力（通常為立式三相電機）位于地面，通過長軸驅動水泵。故使用可靠、維修也比較方便。在無電地區，也可采用柴油機驅動（需在泵軸上加裝皮帶輪或通過齒輪箱傳動）。長軸深井泵有JC型、JC/Q型（淺井用）、JC/S、JC/K型等系列產品。下面重點介紹JC型長軸深井離心泵。（1）使用條件水泵第一級葉輪必須在動水位以下1～3米，一般以2～3米為宜；井水應不含油類，含砂量不大于0.01%，水質中性，不含過量的腐蝕性礦物質；深井井壁應正、直。（2）性能范圍流量5～1500米3/時，揚程20～235米。
一.概述
1.用途：HW混流泵為臥式，單級，單吸，渦殼式混流泵。適用于輸送清水或物理，化學性質類似于水的其它液體。被輸送液體溫度不宜高于50度。廣泛用于農田灌溉，工業和城市排水等多種場合。HW泵的性能范圍：流量90-9000m3/h 揚程3.5-22m。
2. 特點：結構簡單，使用可靠，裝修方便，而且效率高，體型小，重量輕。jdhuiquan4.20
3. 傳動方式：用直接傳動和變速傳動。常用動力機是電動機和柴油機。訂貨 時應明確動力機的型號，以便確定聯軸器和皮帶輪的型號
4.型號說明：以150HW-8S例
150---------泵進出口直徑mm
8------------設計揚程 m
S------------變型代號
農用混流泵A靈壽農用混流泵400HW-7
轉向有一致時，最好采用聯軸器直接傳動。這種傳動方式的優點是：結構緊湊，運轉平穩可靠，傳動效率高。目前用電動機拖動水泵的機組，大都采用聯軸器直接傳動。間接傳動間接傳動就是水泵與動力機的傳動軸不能直聯，而是通過中間傳動裝置直聯接并傳遞動力。這種中間傳動裝置主要是用皮帶傳動和齒輪傳動。齒輪傳動雖然傳動效益高，但制造成本高、價格貴，僅在大型排灌站使用。當水泵與動力機轉速不同，軸線不在同一直線上（垂直或平行），轉向不一致時，一般均采用皮帶間接傳動。皮帶間接傳動的優點是：對轉速、轉向、線軸位置不同的適應性廣，傳動較平穩，過載時皮帶可打滑，不致?lián)p壞機件，結構簡單，使用維修方便。但傳動效益低，需經常調節皮帶長度和更換皮帶。
二.結構和作用
農用混流泵A靈壽農用混流泵400HW-7
When the pump in the work due to cavitation impact or in the winter did not release the pump shell in the water and frozen is also prone to rupture, such as damage is heavier can not be repaired when the new pump shell should be replaced. Pump shafts are generally carbon steel parts, but due to manufacturing quality, use or installation and other reasons are also vulnerable to damage. Pump shaft may appear cracks, bending, shaft neck wear, thread damage, etc., may also appear fracture. If the damage is serious and cannot be repaired, the new shaft should be replaced. The impeller is an important working part of the pump and is made of cast iron. Due to manufacturing quality and use and other reasons are also vulnerable to damage. The impeller may appear cracks, due to cavitation effect on the surface of the bation of a nest eye or perforation, long-term flushing to make the leaves thin or partial grinding, and even crushed by debris. Some defects can be repaired; some defects cannot be repaired, that is, new impellers should be replaced. The bearing of the sliding bearing is cast of copper tin alloy, the wear resistance is very poor, is one of the most easy to wear and burn the wearing parts, the bearing can generally be repaired, can also be replaced with new parts. Rolling bearings generally have an average service life of 5,000 hours.1.HW pump mainly has pump cover, impeller, pump body, pump shaft, bushing, and bearing body and other major components. The pump cover is connected with the pump body and the inlet pipe respectively. 2. There should be an appropriate gap between the pump cover plane and the impeller plane. The gap is too small will produce friction, the gap is too large, will lead to the pump body pressure water a large number of reflux, is the pump efficiency reduction. The suitable gap used in practice is 0.3-0.7mm, and the gap can be adjusted by adding and subtracting the thickness of the paper pad.
3. The shaft is applied to protect the pump shaft and should be replaced in time after wear.
1. Screw holes at the upper end of the pump body, used for filling water diversion or connecting vacuum pump pumping gas to divert water.
2. In order to expand the scope of application of the pump to meet the different needs of users, can cut the outer diameter of the impeller or exchange different perbance of the impeller.
Water pump, valve and accessories technology R & amp; d and Sales: motor, bearings, mechanical seals, bl Products Sales: Pump assembly and maintenance: self-and with all kinds of goods and technology import and export business (except for goods and technologies that the state limits the company to operate or prohibit imports and exports).
訂貨須知：用戶在訂貨（或簽訂技術協議）時，請注明：
1、 使用工況：流量、揚程、漿體濃度及比重、粒徑、吸入形式、傳動方式等；
2、 配套電視：型號、主要技術參數、防護等級、生產廠家等；
3、 其它配套項目：如泵的備件、專用工具、調速裝置等；
4、 其它特殊要求。
規范完全，科技含量高，質量超卓，產品廣泛應用于冶金，礦山。企業資金雄厚。ZTX(R)系列脫硫泵，ZQ型潛渣泵，PW，PW(L)，WD(G)型污水泵，IH系列化工泵等產品?，F(xiàn)在產品除行銷全國各省，自治區以外，并遠銷，東南亞和非洲等，深受用戶好評。IS（R)，D（G），S（H）型清水泵，QJ型潛水泵，ZJ(L)，ZD，ZM（R)，ZH(R)，ZHH，ZL（R)，ZG(P)型渣漿泵，ZN型挖泥泵，ZS型砂礫泵，WQ系列潛污泵，PN，PNJ。河北會泉泵業有限公司是專業出產水泵的大型骨干企業，公司出產的泵型首要有：ISGIS道泵增壓循環泵PNL型泥漿泵ZTL年產各類水泵6000余臺電力。SSH型臥式雙吸泵ZJQ潛水渣漿泵NSQ潛水吸沙泵DDG型礦用多級泵HW型混流泵農用泵ZXZW型臥式自吸泵WFB型自控自吸泵。
